- #Gotek usb floppy emulator software how to#
- #Gotek usb floppy emulator software install#
- #Gotek usb floppy emulator software serial#
- #Gotek usb floppy emulator software upgrade#
- #Gotek usb floppy emulator software software#
You must set it to 3.3V signaling, or you risk damaging the STM32 processor in the GOTEK. IMPORTANT: Be sure you have an adapter that supports 3.3V signaling. You can verify that it is operating correctly by downloading and installing PuTTY or TeraTerm, bridging RX and TX on the USB adapter, and verifying that you see the characters you type in the terminal.
#Gotek usb floppy emulator software serial#
On the right-hand side, you will see the 34 pin floppy connector, with the device select header behind it (more on that later), the power connector, and the serial port/BOOT0 header just behind it.įor the curious, the GOTEK uses the STM32F105:īefore proceeding any further, connect your USB to serial adapter to the Windows PC, and go through any necessary driver installation process. Looking at the image above, to the left, from top to bottom, you can see the 3 digit LED display, USB port, floppy image selection buttons (lower left), and the activity LED (green). Here is what the inside of the GOTEK looks like from the factory (click for larger image): If anyone has, please let me know so I can add that information here. NOTE: I have not tried running it under WINE directly. However - if you are a Linux user (like me), it runs just fine under Windows inside of VirtualBox. Unfortunately, the Online Bootloader Flasher utility only runs under Microsoft Windows.
To flash the new HxC2001 firmware onto the STM32 processor in the GOTEK, you will need to connect a PC running Windows to the serial port on the GOTEK emulator. Once you complete the purchase, you will receive an email that contains login credentials to use with the Online Bootloader Flasher utility. You only have to buy the bootloader for the GOTEK once. (Note: It also enables future upgrades by placing new firmware on a USB stick, inserting the stick, and powering on the GOTEK with both buttons pressed. The bootloader enables the GOTEK emulator to load the official HxC2001 firmware from a USB stick. For STM32 based floppy emulators like the GOTEK, there is a nominal charge (about $12US at the time of this writing) for the new bootloader.
#Gotek usb floppy emulator software install#
The HxC2001 firmware itself is free, but to install it on non-HxC2001 hardware, it requires a special bootloader.
#Gotek usb floppy emulator software upgrade#
Upgrade Process Step 1 - Purchase an STM32 Bootloader from the HxC2001 project. Here are some pictures of the parts I used (click for larger version): (1) 0.91" OLED 128x32 Display (optional) (eBay search here)Įven if you don't have any of these on hand, if you shop carefully, you can get the parts for $35US or less. (1) 1 header jumper (you can borrow this from one of the other headers on the GOTEK during programming) (1) 4-pin header strip (eBay search here) (1) 5-pin header strip (eBay search here) (1) USB-to-serial adapter with 3.3V output (eBay search here) (1) GOTEK Floppy Drive Emulator (eBay search here) You can find the "official" instructions here.
To illustrate the steps for someone trying this for the first time (and to add a few tips and suggestions), I've put together this step-by-step guide.
#Gotek usb floppy emulator software how to#
The HxC2001 website provides fairly clear instructions on how to upgrade a GOTEK floppy drive emulator to use HxC2001 firmware. With a few simple steps, you can convert a very inexpensive (<$30US) GOTEK emulator into a retro-floppy emulator with excellent compatibility for older machines. The good news is that the HxC2001 project has ported their excellent firmware to the GOTEK floppy emulator. This is a problem for using it in older computers that expect a Shugart-style floppy interface unless you're willing to do some custom cabling. The interface it presents to the computer is IBM-compatible only.
#Gotek usb floppy emulator software software#
It works, but the firmware is much more limited and the software to install images is less than user-friendly. Recently, GOTEK has created a less expensive but less capable unit sold on eBay and Amazon. HxC2001 is quite capable, but can also be quite expensive per drive (upwards of $100US per unit). Over time support for different drive types and floppy image formats has been added. To address this problem for his Atari ST, Jean-Fancois Del Niro created HxC2001, which is a hardware-based floppy drive emulator. Finding working 8" or 5.25" floppy drives is becoming increasingly difficult. Machines from this period commonly have 8" or 5.25" floppy drives. I enjoy collecting older computers, particularly ones from the mid-to-late `70s through the early `80s that run CP/M. Upgrading the GOTEK Floppy Drive Emulator
0 kommentar(er)
